Vines Wristers

Vines Wristers 1000

LOOM:  Sock Loom 2, 31 pegs.

YARN:  Approx 120 yds of worsted weight wool blend. Noro Taiyo in color 24 was used in sample.

NOTIONS: Knitting tool, tapestry needle, 6 small buttons.

GAUGE: 18 x 21 rows=4”

SIZE: 6.5” L x 10” W (width goes around hand).

ABBREVIATIONS

K=knit stitch

P=purl stitch

CO=Cast on

St(s)=stitch(es)

Rep=repeat

k2tog=knit two stitches together, right-slanting

ssk=knit two stitches together, left-slanting

yo=yarn over (ewrap peg)

 

INSTRUCTIONS

Left-Hand Wrister

Cast on 31 sts. (Cast on from Right to Left on the loom).

Row 1: p to end (From Left to Right on the loom).

Row 2: k3, *yo, k2, ssk, k2tog, k2, yo, k1; rep from * to last stitch, k1.

Row 3: k to the end.

Row 4: As Row 2.

Repeat Row 1-4: until you reach row 36.

Next row: p to the end.

Next row: k5, BO4, k3, *yo, k2, skk, k2tog, k2, yo, k1; rep from * to last st, k1.

Next row: k22, CO4, k to the end.

Next row: As Row 2

Repeat Rows 1-4.

Bind off with basic removal method. Weave ends in. Steam block to open lace stitch pattern.

 

Right-Hand Wrister

Cast on 31 stitches. (Cast on from Right to Left on the loom).

Row 1: p to end of row. (From Left to Right on the loom.

Row 2: k2, *yo, k2, ssk, k2tog, k2, yo, k1; rep from * to last 2 sts, k2.

Row 3: k to the end.

Row 4: As Row 2.

Repeat Row 1-4: until you reach row 36. **

Next row: p to the end.

Next row: k2, [yo, k2, skk, k2tog, k2, yo, k1]2 times, k2, BO4, k5.

Next row: k5, CO4, k to end.

Next row: As row 2.

Repeat Rows 1-4.

Bind off with basic removal method. Weave ends in. Steam block to open lace stitch pattern.

ASSEMBLY

Before assembly, block both panels. The buttons will be placed on the 10th ridge of the panel, counting from the scalloped edge. Or, on the 2nd ridge from the straight edge. Place one button on each scalloped crest. Sew the buttons in place with regular thread, not yarn. The buttons are located one ridge right before the thumbhole.

The buttons will be placed on the 10th ridge of the panel, counting from the scalloped edge. Or, on the 2nd ridge from the straight edge. Place one button on each scalloped crest. I found sewing the button with regular thread easier than with yarn. The buttons are located one ridge before the thumbhole.

Collage of Vine Wristers

SUPPLEMENTAL INSTRUCTION

Breakdown of lace row (instructions that start with *, or Row 2/Row 4 of chart)

*yo, k2, ssk, k2tog, k2, yo, k1.

Over 9 stitches.

9 stitches are numbered from Right to Left as follows: 9-8-7-6-5-4-3-2-1

Step 1: Move loop from peg 4 and hold it.

Step 2: Move loop from peg 3 to 4.

Step 3: Place loop from Step 1 back onto peg 4.

Step 4: Move loop from peg 2 to peg 3; from peg 1 to peg 2.

Step 5: Move loop from peg 5 to peg 6.

Step 6: Move both loops from peg 6 to peg 5. Step 7: Move loop from peg 7 to peg 6; from peg 8 to peg 7.

Pegs 1 and 8 are empty.

Pegs 4 and 5 have two loops on them.

Work the stitches as follows: YO on peg 1, k to peg 7, YO on peg 8, k peg 9. Pegs that have two loops, treat both loops as one loop.

PIN ME


9 thoughts on “Vines Wristers

  1. I have just purchased my first knitting board,,the sock 2. I made my first sock was a bit funky. Any tips you can give me?

  2. Lovely!
    Glad you have posted the instructions. The ‘free download’ pdf of this has some funky ending instruction, talking about using the kitcheners stitch to finish the toe…and to be careful when putting beads on socks since they might not be comfortable to wear with shoes!
    lol

    After the Peaks wristers pattern in one of the books (my current project), this one should be easy enough to figure out. 🙂 (hoping!)

Leave a Reply

Your email address will not be published. Required fields are marked *